YG-1 E5245 Carbide Square Nose End Mill, TIALN Multilayer Finish, 30 Deg Helix, 4 Flutes, 3" Overall Length, 0.75" Cutting Diameter, 0.75" Shank Diameter

You looking to find the "YG-1 E5245 Carbide Square Nose End Mill, TIALN Multilayer Finish, 30 Deg Helix, 4 Flutes, 3" Overall Length, 0.75" Cutting Diameter, 0.75" Shank Diameter" Good news! You can purchase YG-1 E5245 Carbide Square Nose End Mill, TIALN Multilayer Finish, 30 Deg Helix, 4 Flutes, 3" Overall Length, 0.75" Cutting Diameter, 0.75" Shank Diameter with secure price and compare to view update price on this product. And deals on this product is available only for limited time.

Price: $98.71    

Product Feature

• Suitable for general-purpose machining on hardened and high-alloy steel, cast iron, and chromium-nickel steel
• Stub length increases the strength of the tool, making it less likely to break in the workpiece
• Four flutes produce a better finish than fewer flutes
• Titanium aluminum nitride (TiAlN) coating lubricates the end mill for high-temperature stability and abrasion resistance at high cutting speeds, offering better heat resistance than TiN and TiCN coatings
• Carbide can run at higher speeds than high-speed or cobalt steel, resisting wear and high cutting temperatures

Product Description

The YG-1 E5245TF TiAlN-coated carbide stub-length square nose end mill has four flutes, a center-cutting design, and a 30-degree helix angle for general-purpose machining on hardened and high-alloy steel, cast iron, and chromium-nickel steel. The stub length increases tool strength and makes it less likely to break in the material being machined. It is best used when depth of cut is shallow. Four flutes produce a better finish than fewer flutes. The tool� �s square end creates sharp, unrounded cuts. The center-cutting design has cutting teeth at the end of the tool, so it can be fed into the workpiece like a drill bit. The 30-degree helix angle supports general-purpose applications. It balances lower angles’ strong cutting edge for difficult-to-machine materials with higher angles � increased cutting action.

The TiAlN coating resists heat better than TiN and TiCN coatings, increasing tool life and performance. It also offers increased hardness compared to TiN and may reduce the need for lubricants based on the application. The carbide substrate is harder than high-speed or cobalt steel, making it more wear resistant at high speeds and providing longer tool life. Cutting diameter tolerance is + 0.0000 to - 0.0012". The round shank accommodates a range of tool holders.

End mills are designed to remove material and create multi-dimensional shapes and profiles. They have cutting edges along the outside diameter and flutes that remove chips from the cutting area and allow cooling fluids to enter. If heat is not reduced effectively, the tool � s cutting edges will dull and additional material buildup can occur. The number of flutes can range from two to eight. Two-flute designs offer the most efficient chip removal, but more flutes provide a smoother finish. The shank is the end of the tool held in place by a tool holder or machine. Center-cutting end mills can create three-dimensional shapes and profiles, and make plunge cuts similar to a drill bit. Non-center-cutting end mills are for applications such as peripheral milling and finishing, but cannot make plunge cuts.

YG-1 manufactures drills, taps, end mills, and rotary tooling. The company, founded in 1981, is headquartered in South Korea and has a U.S. office in Vernon Hills, IL.

YG-1 E5245 Carbide Square Nose End Mill, TIALN Multilayer Finish, 30 Deg Helix, 4 Flutes, 3" Overall Length, 0.75" Cutting Diameter, 0.75" Shank Diameter Review

I purchased both cobalt and carbide mills to see which I might prefer and I'm torn. I am unable to decide a preference to which I prefer and will go on to say that I would use either carbide or cobalt over HSS any day. The price is not that much more for these mills and I'll go on to say that in downtime and speed of milling, might make these cheaper than HSS in those respects, adding the longevity before sharpening or replacement, I believe they are worth it even more!

Most of the consumer Reviews tell that the "YG-1 E5245 Carbide Square Nose End Mill, TIALN Multilayer Finish, 30 Deg Helix, 4 Flutes, 3" Overall Length, 0.75" Cutting Diameter, 0.75" Shank Diameter" are high quality item. You can read each testimony from consumers to find out cons and pros from YG-1 E5245 Carbide Square Nose End Mill, TIALN Multilayer Finish, 30 Deg Helix, 4 Flutes, 3" Overall Length, 0.75" Cutting Diameter, 0.75" Shank Diameter ...