JET 321373 BD-920N 9-Inch Swing-by-20-Inch between Centers 3/4-Horsepower Benchtop Lathe, 115-Volt 1-Phase

You looking to find the "JET 321373 BD-920N 9-Inch Swing-by-20-Inch between Centers 3/4-Horsepower Benchtop Lathe, 115-Volt 1-Phase" Good news! You can purchase JET 321373 BD-920N 9-Inch Swing-by-20-Inch between Centers 3/4-Horsepower Benchtop Lathe, 115-Volt 1-Phase with secure price and compare to view update price on this product. And deals on this product is available only for limited time.

Price: $2,299.99   

Product Feature

• 3/4 HP 115Volt Motor
• 6 Spindle Speeds 130-1,200 RPM
• 25/32" Spindle Hole, 1 1/2" x 8 thread per inch spindle
• 235 pounds
• Shown with optional stand

Product Description

60 longitudinal feeds from 0.0006 to 0.037in. Spindle is mounted in tapered roller bearings and has MT-#3 taper with 1 1/2in. x 8 TPI spindle nose. Cross slide travel of 5in. Tailstock adjusts for taper cuts. Lathe has hardened and ground bedways, 7in. 4-jaw and 4in. 3-jaw chucks, faceplate, 4-way tool post, quick change gear box, threading dial and tool kit. Single phase motor. Stand Included: No, Carriage Travel (in.): 16, HP: 3/4, Thread Cutting (mm): .05-3, Volts: 115, Width Between Centers (in.): 20, Thread Cutting (in.): 8-56 TPI, Speed (RPM): 130-2,000, Spindle Speeds (qty.): 6

JET 321373 BD-920N 9-Inch Swing-by-20-Inch between Centers 3/4-Horsepower Benchtop Lathe, 115-Volt 1-Phase Review

I was looking for a benchtop lathe with a little more grunt and capability than the smaller, hobby-type machines, and without spending a ton of money. The lathe arrived well crated and covered with preservative. Plan on using up a roll of paper towels getting this stuff off. Once mounted on my workbench, I checked the spindle for runout with a coax indicator and also checked the tailstock alignment. Both were on the money. I obtained a live center, drill chuck, and a set of tool holders locally, and was off and running. First project was a steering tube for an outboard motor, that required a 12" length of aluminum stock to be turned to 7/8" OD and a 14-TPI thread cut. Both operations went extrememly well. Vibration is very low and this machine is solid.

Some gripes: When cutting threads coarser than 14 TPI, the end gearing arrangement prevents the access cover from being closed. This I see as a potential safety issue. I would like to see a power cross feed added, even if it added to the cost of the machine. Finally, I would like to see the inside of the tailstock taper keyed for the drill-chuck arbor.

All said, this is a lot of lathe for the money. I see from other reviews that some people aren't happy, but my experience has been positive so far. I've done this stuff for a living on a $20,000 toolroom lathe and this little JET does many things just as well. It is a small machine with limited power, but should serve most home machinists very well when used within its limitations.

Most of the consumer Reviews tell that the "JET 321373 BD-920N 9-Inch Swing-by-20-Inch between Centers 3/4-Horsepower Benchtop Lathe, 115-Volt 1-Phase" are high quality item. You can read each testimony from consumers to find out cons and pros from JET 321373 BD-920N 9-Inch Swing-by-20-Inch between Centers 3/4-Horsepower Benchtop Lathe, 115-Volt 1-Phase ...